Fiber Media Converter Oman, 10/100M Single Fiber BiDi SC, A and B Pair

A fiber media converter turns RJ45 Ethernet into light, so your network runs far past 100 meters of copper. This single fiber media converter works only as an A and B pair on single mode fiber. It supplies no PoE. Aurex Smart Systems supplies this fiber media converter in Oman as a BiDi media converter with one SC port. Installers use this fiber to Ethernet converter as a media converter for CCTV on links up to 20 km.

Fiber Media Converter Oman: Why Copper Stops at 100 Meters

Ethernet over copper cable is limited to 100 meters per run. A gate camera, a guard room or a second building is often much further away. A fiber media converter at each end carries the same network over glass instead.

Fiber also ignores lightning surges and electrical noise from motors and generators. That matters on farms, factories and long boundary walls. One fiber media converter in Oman pairs with one at the far end. The two act like a long patch cable.

Single Fiber Media Converter: How the A and B Pair Works

A single fiber media converter sends and receives on one strand of fiber. It does this by using two different wavelengths, one for each direction. That is why the units come as an A and B pair.

Fit an A unit at one end and a B unit at the other. Two A units or two B units will not link, because they transmit on the same wavelength. Check the label on each box before you install.

A single fiber media converter also saves cores. It uses one core per link, while dual fiber units need two. So a 12 core cable carries 12 camera links with this model, or six with dual fiber units.

BiDi Media Converter Specifications

This BiDi media converter is a plug and play unit. It needs no settings or software.

The 20 km figure is typical. Real distance depends on fiber quality and on how many splices and connectors sit on the route.

Media Converter for CCTV: A Typical Camera Link

The most common job for a media converter for CCTV is a camera that sits too far from the recorder. Here is how the link is built, from the camera back to the recorder.

1. The outdoor IP camera plugs into a small PoE switch or PoE injector for power.
2. The switch connects to the A unit with a short RJ45 cable.
3. The A unit sends the signal over one core of single mode fiber optic cable.
4. At the far end, the core is terminated in a fiber optic patch panel.
5. An SC to SC fiber patch cord links the panel to the B unit.
6. The B unit plugs into the network switch beside your NVR.

Remember that the converter gives no power to the camera. Plan a PoE switch or injector at the camera end, with a mains socket for it.

A media converter for CCTV is also the simple fix for gate cameras, car parks and boundary walls. In each case the camera sits beyond the copper limit. One media converter for CCTV pair carries one camera, or a small group of cameras behind a switch.

Heat in Oman: Where to Mount the Fiber to Ethernet Converter

The fiber to Ethernet converter is rated up to plus 60°C. A metal box in direct sun can run hotter than that in an Omani summer. Heat is the most common reason a link drops in the afternoon and returns at night.

Mount the unit indoors wherever you can. Outdoors, use a shaded and ventilated enclosure, away from walls that face the sun. Give the 5V adapter a protected mains socket at both ends. Keep each fiber to Ethernet converter off the cabinet floor, where dust and heat collect.

What You Need Besides the BiDi Media Converter

The pair converts the signal, but it does not complete the link alone. Each item below is a separate part.

Use single mode patch cords only. A multimode cord on a BiDi media converter causes high loss or no link at all.

100M or Gigabit: Is This Single Fiber Media Converter Enough?

This single fiber media converter runs at 10/100M. That suits one camera, an access control panel or a small office link. A typical IP camera stream uses only a small share of 100 Mbps.

Many cameras on one fiber can fill the link, though. For a large site or a building backbone, ask us about gigabit SFP links instead. Send us the camera count and we size the single fiber media converter link for you.

Get a Quote for a Fiber Media Converter in Oman

We quote every fiber media converter in Oman as a complete link. Most jobs need cable, panels and cords as well. Send these details on WhatsApp:

• Distance between the two ends
• How many links you need, and how many pairs
• Whether fiber is already installed, and its type
• What connects at each end, such as a camera, switch or NVR
• Whether the units sit indoors or in an outdoor box

We supply customers in Muscat, Sohar, Nizwa, Salalah, Sur, Duqm and every other governorate.

Fiber to Ethernet Converter Questions

Does a media converter for CCTV come as a pair?

Yes. You need one unit at the camera end and one at the recorder end. With this model, one end must be an A unit and the other a B unit.

Can a BiDi media converter use multimode fiber?

No. This BiDi media converter is built for single mode OS2 fiber only. Multimode cable or patch cords will cause high loss or no link.

Does the fiber to Ethernet converter supply PoE?

No. The fiber to Ethernet converter only converts the signal. Power the camera with a separate PoE switch or PoE injector.

How much does a fiber media converter cost in Oman?

The price depends on how many pairs you need and what else the link needs. We quote each job, so send your details on WhatsApp and we reply with a price.

Fiber Media Converter Oman: Order from Aurex Smart Systems

Aurex Smart Systems supplies the fiber media converter Oman installers ask for, matched to your fiber and your equipment. Call or WhatsApp +968 78109286, or email info@aurexsmart.com. We answer every day from 8:00 am to 10:00 pm.